Radiant RS 30 E Uživatelský manuál

IDEAL CLASSICRS30, RS40, RS50 & RS60CAUTION: To avoid the possibility of injury during theinstallation, servicing or cleaning of this appliance, c

INSTALLATlONFITTING THE FLUE ASSEMBLY - EXTENSION DUCTS12 FITTING THE FLUE ASSEMBLY. Duct lengths up to 400 mm (16 in.)FLUE TERMINAL ASSEMBLY13 EX

WARNING: Theappliance MUST beefficiently earthed.A mains supply of240 V ~ 50 Hz isrequired.All external controls and wiringMUST be suitable for mainsv

INSTALLATION18 MID POSITION VALVEPumped only19 TWO SPRING CLOSED VALVESPumped only20 HONEYWELL 'C' PLANNotes:1. Some earth wires are omitte

thermocouple output is between 8 and 15 mV closedcircuit.The pilot flame is factory set and no adjustment ispossible. If the pilot flame is incorrect

5. With the system HOT, examine all water connections forsoundness. Then turn OFF the gas, electricity and watersupplies to the appliance and drain do

SERVICING1 SCHEDULEGENERAL - CLEANING AND ADJUSTMENT2 BOILER CASING REMOVALTo ensure the continued safe and efficient operation of theappliance, it i

5 CLEANING THE BURNER AND PILOT ASSEMBLYRefer to Frame 3 for illustration of the procedure below.1. Brush off any deposits that may have fallen onto t

3. Removethe suppressor by removing the screwretaining the terminal block, lifting theterminal block and unscrewing the suppressor leadconnections4. F

18SERVICINGREPLACEMENT OF PARTS14 OVERHEAT THERMOSTAT REPLACEMENT Fitted for sealed systems only15 SPARK ELECTRODE AND LEAD REPLACEMENT16 THERMOCOU

1. Refer to Frame 8.2. Remove the burner and air boxassembly. Refer to Frame 3.3. Remove the two front tie rods.4. Remove the two side panel retainin

Boiler Size RS 30 RS 40 RS 50 RS 60Boiler input MINIMUM kW 5.8 11.3 15.0 18.8To obtain gas consumption (Btu/h) (19 800) (38 500) (51 200) (64 100)(a)

20Back panelmountingbracketProgrammerSee note 5Programmer mounting bracketStainless steel lid, see note 5Terminal strip,see note 8.See note 3DETAIL

21SERVICINGEXPLODED VIEWSLEGEND (Numbers up to 39 relate to the B.G. spares list)1. Heat exchanger 8. Collector hood 26. Boiler thermostat 39. Ove

FAULT FINDING26 PILOT WILL NOT LIGHTNOYESNOYES27 PILOT WILL NOT STAY LIT WHEN THE GAS VALVE BUTTON IS RELEASEDClean the contracts and reconnect secu

Key No. G.C. Part No. Description No. Off Maker's Part No.11 319 493 Sightglass assembly kit 1 160 079 33315 Main burner386 138 AEROMATIC No. AC

SERVICINGSHORT LIST OF PARTS - COMPONENT DIAGRAMS29 SHORT PARTS313030 BOILER CASING ASSEMBLYCustomer Care & Technical SupportPlease use the foll

INTRODUCTION - GAS SUPPLY3 GENERALIMPORTANT. These appliances are certificated by the BritishStandards Institution for safety and performance. I

GENERALAn existing meter should be checked, preferably by the gasregion, to ensure that the meter is adequate to deal with therate of gas supply requi

The boiler is fitted with a special drain plug which is providedto drain the BOILER ONLY in the event of the system drainplug being unable to do so.Th

INSTALLATIONFLUE PACKS Note: All flue packs contain 2 sachets of sealant.PACK B. Contains a balanced flue terminal suitable for wall thicknesses fro

INSTALLATION 3 BOILER WATER CONNECTIONS. Open vented systems. SYSTEM DESIGN1. This appliance is NOT suitable for use in a direct hot watersystem2. If

SYSTEM DESIGN - BOILER DIMENSIONS & CLEARANCESINSTALLATION5 REQUIREMENTS FOR CORRECT GRAVITY HOT WATER PERFORMANCE7 CLEARANCES & TERMINAL OPE

INSTALLATION PREPARING THE WALL - MOUNTING THE BOILER9 PREPARING THE WALL10 PREPARING THE BOILER11 MOUNTING THE BOILER91. Lift the boiler onto the wa